Next Previous Up Contents
Next: Examples
Up: tmulti: Writes multiple tables to a single container file
Previous: tmulti: Writes multiple tables to a single container file

B.39.1 Usage

The usage of tmulti is

   stilts <stilts-flags> tmulti in=<table> [<table> ...] ifmt=<in-format>
                                multi=true|false istream=true|false
                                icmd=<cmds> out=<out-file> ofmt=<out-format>
If you don't have the stilts script installed, write "java -jar stilts.jar" instead of "stilts" - see Section 3. The available <stilts-flags> are listed in Section 2.1. For programmatic invocation, the Task class for this command is uk.ac.starlink.ttools.task.MultiCopy.

Parameter values are assigned on the command line as explained in Section 2.3. They are as follows:

icmd = <cmds>       (ProcessingStep[])
Specifies processing to be performed on each input table as specified by parameter in, before any other processing has taken place. The value of this parameter is one or more of the filter commands described in Section 6.1. If more than one is given, they must be separated by semicolon characters (";"). This parameter can be repeated multiple times on the same command line to build up a list of processing steps. The sequence of commands given in this way defines the processing pipeline which is performed on the table.

Commands may alternatively be supplied in an external file, by using the indirection character '@'. Thus a value of "@filename" causes the file filename to be read for a list of filter commands to execute. The commands in the file may be separated by newline characters and/or semicolons, and lines which are blank or which start with a '#' character are ignored. A backslash character '\' at the end of a line joins it with the following line.

ifmt = <in-format>       (String)
Specifies the format of the input table as specified by parameter in. The known formats are listed in Section 5.1.1. This flag can be used if you know what format your table is in. If it has the special value (auto) (the default), then an attempt will be made to detect the format of the table automatically. This cannot always be done correctly however, in which case the program will exit with an error explaining which formats were attempted. This parameter is ignored for scheme-specified tables.

The same format parameter applies to all the tables specified by in.

[Default: (auto)]

in = <table> [<table> ...]       (TableProducer[])
Locations of the input tables. Either specify the parameter multiple times, or supply the input tables as a space-separated list within a single use.

The following table location forms are allowed:

Compression in any of the supported compression formats (Unix compress, gzip or bzip2) is expanded automatically.

A list of input table locations may be given in an external file by using the indirction character '@'. Thus "in=@filename" causes the file filename to be read for a list of input table locations. The locations in the file should each be on a separate line.

istream = true|false       (Boolean)
If set true, the input table specified by the in parameter will be read as a stream. It is necessary to give the ifmt parameter in this case. Depending on the required operations and processing mode, this may cause the read to fail (sometimes it is necessary to read the table more than once). It is not normally necessary to set this flag; in most cases the data will be streamed automatically if that is the best thing to do. However it can sometimes result in less resource usage when processing large files in certain formats (such as VOTable). This parameter is ignored for scheme-specified tables.

The same streaming flag applies to all the tables specified by in.

[Default: false]

multi = true|false       (Boolean)
Determines whether all tables, or just the first one, from input table files will be used. If set false, then just the first table from each file named by in will be used. If true, then all tables present in those input files will be used. This only has an effect for file formats which are capable of containing more than one table, which effectively means FITS and VOTable and their variants.

[Default: false]

ofmt = <out-format>       (String)
Specifies the format in which the output tables will be written (one of the ones in Section 5.1.2 - matching is case-insensitive and you can use just the first few letters). If it has the special value "(auto)" (the default), then the output filename will be examined to try to guess what sort of file is required usually by looking at the extension. If it's not obvious from the filename what output format is intended, an error will result.

Not all output formats are capable of writing multiple tables; if you choose one that is not, an error will result.

[Default: (auto)]

out = <out-file>       (uk.ac.starlink.util.Destination)
The location of the output file. This is usually a filename to write to. If it is equal to the special value "-" the output will be written to standard output.

[Default: -]


Next Previous Up Contents
Next: Examples
Up: tmulti: Writes multiple tables to a single container file
Previous: tmulti: Writes multiple tables to a single container file

STILTS - Starlink Tables Infrastructure Library Tool Set
Starlink User Note256
STILTS web page: http://www.starlink.ac.uk/stilts/
Author email: m.b.taylor@bristol.ac.uk
Mailing list: topcat-user@jiscmail.ac.uk